From:http://www.sinocmpinjector.com
Abstract: Injector is a component with a high failure rate of a diesel engine. It analyzes the problems such as dripping oil from the injector, the inadequate seal between the needle valve and valve body, and seizure. Problems to be paid attention to during inspection, and a treatment method for worn injector parts was proposed.
The
fuel injector is one of the key components of the diesel fuel system and is also a wearing part. The technical status of the injector has a direct impact on the performance of the diesel engine. Whenever the vehicle has insufficient power and abnormal smoke exhaust, the first thing that the repairman thinks of is to check the fuel injector to see if its atomization quality, fuel injection pressure, and sealing performance are satisfactory. If these three performance indicators are not satisfactory, find and troubleshoot further.
1 Common fault analysis of injector
1.1 Drip oil from the injector
Failure phenomenon: fuel injection continues, nozzle holes are blocked, fuel can not be atomized, fuel injection is uneven, poor stability, working knock, exhaust smoke, carbon deposits increase, resulting in decreased engine power, increased fuel consumption, and increased wear.
Failure cause analysis:
(1) the needle valve and needle valve body sealing cone surface wear severely, and groove marks appear, which widens the contact surface of the cone sealing ring belt, deforms the cone surface, increases the roughness, and causes oil dripping from the injector. Carbon deposits formed near the spray holes and even blocked the spray holes.
(2) The higher the residual pressure of the high-pressure fuel pipe (that is, the pressure when the high-pressure fuel pipe is not injecting fuel between the two injections of the injector), the more oil drips from the injector, and the main reason affecting the residual pressure is the oil valve Pieces. The oil dripping faults of the fuel injector is not all on the fuel injector but have a close relationship with the tightness of the valve assembly. Abnormal wear of the oil outlet valve will cause oil dripping from the injector.
(3) Insufficient sliding between needle valve and needle valve body guide surface, work retardation, or serious wear of needle valve and needle valve body guide surface, inadequate contact between the needle valve body and injector body, or needle valve and needle The sealing cone surface of the valve body is cushioned by mechanical impurities, and if it is not tightly closed, the fuel injection nozzle will drip oil.
1.2 Injector needle valve and valve body are not tightly sealed and bite
Symptoms of failure: The low-pressure oil circuit is unblocked. After the speed control handle is put to the fuel supply position, the diesel engine is turned. Individual cylinders cannot hear the sound of fuel injection from the injector. The exhaust pipe emits white smoke and is not easy to catch fire. When the diesel engine catches fire, the exhaust pipe still emits smoke, and the idling speed is not stable, accompanied by the gasping sound of "Teng, Teng", and the knocking of the cylinder at high speeds and throttles. When the temperature of the diesel engine rises, the exhaust pipe emits black smoke, the fuel injector burns, and it catches fire. Disconnect the high-pressure tubing from the missing leg cylinder. The diesel exhaust pipe no longer smoked, and the sound of knocking cylinders disappeared. However, there is an exhaust phenomenon at the high-pressure oil pipe joint of the injector and foam is discharged.
Failure cause analysis:
(1) During the operation of the diesel engine, the high-pressure diesel pumped from the fuel injection pump carried some mechanical impurities, entered the fuel injector and adhered to the sealing cone of the needle valve body, causing card issuance and cushioning, resulting in contact. Not tight.
(2) Due to the ablation of high-pressure and high-temperature gas in the combustion chamber, and frequent washing of mechanical impurities in the fuel, pits, and pits appear on the sealing ring of the needle valve and the needle valve body, resulting in the needle valve and the valve body The sealing performance deteriorates, and the phenomenon is that the oil return amount at the oil return hole of the injector increases. In this way, the high-pressure and high-temperature gas in the combustion chamber during work will enter the annular oil chamber of the injector. Under the action of high temperature, the injector needle valve and the valve body are thermally expanded and bite each other.
(3) Too much mechanical impurities in diesel will also cause the impurities to enter between the needle valve and the guide surface of the valve body and die. Because the needle valve of the injector and the valve body is seized, the atomization performance of the diesel becomes poor, which makes the injection time too short and extends slightly backward, resulting in a short ignition period, which makes the diesel engine rough. Therefore, the diesel engine issued " "Teng, Teng" sound and obvious knock sound.
(4) The
injector needle valve and valve body are not tightly sealed or bite in the open position, causing the high-temperature gas in the combustion chamber to enter the annular oil chamber of the injector, causing the injector to be hot. If the diesel engine is shaken in this state, the compressed air generated in the cylinder will enter the annular oil chamber and oil passage through the opened nozzles and will be discharged from the high-pressure oil pipe, thus showing the phenomenon of high-pressure oil pipe exhaust.
2 Injector inspection
The inspection and adjustment of the injector assembly at some service points were too extensive. Some only check and adjust the starting fuel injection pressure, reducing some items that should not be simplified. This is not correct. We believe that the adjustment should be carried out according to the process specifications. Not only should the standard injection pressure be checked and adjusted, but also the spray cone angle and injection quality should be further checked according to the specific situation, especially for the tightness check of the injector. Get full attention.
Checking the tightness of the injector: performed on the injector tester, taking the porous long injector as an example, increasing the predetermined pressure of the injector tester to 23 to 24 MPa, and adjusting the injection pressure of the injector As high as 24 to 25 MPa, when the injector tester pressure is reduced from 20 MPa to 18 MPa, the standard injector should last 9 to 20 s, and the allowable use should not be less than 9 s.
It is worth noting: First, the
injector tester must meet the technical requirements, the high-pressure oil circuit should be tight, and the tightness of the oil valve assembly itself on the tester should be good. Exclude the air in the oil circuit, block the high-pressure oil outlet joint, continue to supply oil and increase the pressure to increase the predetermined pressure to 23 to 24 MPa. When the tester pressure is reduced from 20 MPa to 18 MPa, it should last no less than 3 minutes. Secondly, check the injectors no less than twice, and take the average value. And the difference between the two adjacent durations must not be greater than 2 s for shaft pins and flat plates; for porous long types, it must not be greater than 3 s.
3 Troubleshooting
After the injector needle valve and valve body are not tightly sealed, biting each other or dripping oil, the injector should be removed first and the needle valve and valve body should be cleaned with clean diesel. If there are slight pits and pits on the sealing cone of the needle valve and the valve body, it should be ground on special equipment or pliers (note that the abrasive paste must not enter the sliding surface of the needle valve and the valve body), and then Grind with engine oil until the pits and pits on the sealing cone surface of the needle valve and valve body disappear and appear black and bright. For the needle valve and the valve body that is bitten by the needle, the needle valve should be taken out with pliers, and then cleaned in clean diesel oil. Then use a relatively fine oil stone or sand bar to smooth the stuck protrusion. (Be careful not to damage other parts), make the needle valve slide freely in the valve body, and then use the polishing paste and oil to grind the sealing cone surface to the above requirements. If the pits and pits on the sealing cone surface of the needle valve and the valve body are too deep and cannot be repaired, the new injector should be replaced, and the injection pressure and fuel atomization quality should be adjusted on the test bench or car. Make it meet the requirements for use.
The fuel injector is one of the most important devices in the fuel supply system of the diesel engine, which can spray the diesel oil into the cylinder uniformly, finely and evenly to make it mix with the compressed air in the cylinder evenly and form a good combustible mixture. Its working quality directly affects the power, economy and service life of diesel engines. In the process of using and maintaining the diesel engine, some minor negligence may lead to major faults.
(2) When the fuel injector is installed after replacement, cleaning or troubleshooting, the appropriate thickness of the sealing adjusting pad shall be selected according to the requirements of technical conditions to ensure the depth of the fuel injector into the combustion chamber. So as to ensure the formation quality of the combustible mixture. When assembling the fuel injector after cleaning and troubleshooting, make sure that the coupling parts are used in pairs. The spray needle and nozzle are all components with grinding matching, and the matching clearance is 0.002-0.004 mm. In case of any pairing, the sealing between the spray needle and the nozzle will be affected. When assembling the injector, the impurities in the inner cavity of the nozzle shall be completely removed to prevent the injector from sticking (the upper clamp is not sealed, and the lower clamp is not injected).
